SKU: 5399944681

Blackmagic Design Spares - Camera PCC6KPro - PCB Main

Sale price$7412.67 Regular price$8236.30
Save 10%

Pay in installments of $2059.07 with ShopPay, AfterPay and Klarna

Shipping Estimate
USA
  • USA
  • CAN

Ships within 48 hours · Estimated delivery Jul 29 - Aug 3

Promo Codes Available:

For Your Every Summer RSVP, with Code: SUMMER15

Description

Blackmagic Design Spares - Camera PCC6KPro - PCB MainThe Blackmagic Design Spares Camera PCC6KPro PCB Main is the "brain" and central nervous system of the Pocket Cinema Camera 6K Pro. This is the most complex and expensive spare part available for the camera, as it houses the image processor, the BRAW encoding engine, and the primary power management system. Because the 6K Pro features a unique architecture (internal ND filters and a high draw $1,500\text{nit}$ screen), this board is not

The Blackmagic Design Spares - Camera PCC6KPro - PCB Main is the "brain" and central nervous system of the Pocket Cinema Camera 6K Pro. This is the most complex and expensive spare part available for the camera, as it houses the image processor, the BRAW encoding engine, and the primary power management system.

Because the 6K Pro features a unique architecture (internal ND filters and a high-draw $1,500\text{nit}$ screen), this board is not interchangeable with the standard Pocket 6K or 6K G2 boards.


Core Responsibilities

The Main PCB manages every critical digital function of the camera:

  • Image Processing: Houses the FPGA (Field Programmable Gate Array) that debayers the raw sensor data and converts it into Blackmagic RAW or ProRes.

  • Storage Management: Controls the high-speed data lanes for the CFast 2.0 slot, the SD UHS-II slot, and the USB-C $3.1\text{ Gen }1$ port for external recording.

  • ND Filter Control: Manages the precision stepper motors that move the physical glass ND filters in front of the sensor.

  • Screen Driving: Features a dedicated high-bandwidth LVDS interface to drive the 5-inch HDR tilting touchscreen.

When to Replace the Main PCB

Replacing the motherboard is usually a last resort when the camera is "bricked" or has suffered catastrophic electronic failure:

  • SDI/HDMI/USB-C Controller Failure: If the camera no longer outputs a signal or refuses to see external drives, and the physical ports are not damaged, the controller chips on the Main PCB have likely "fried."

  • Power Rail Failure: If the camera refuses to turn on with any power source (AC or battery) and the internal Power Assembly Cable has been verified as working.

  • Systemic "Freezing": If the camera constantly hangs on the splash screen or crashes mid-record even after a firmware re-install.

  • Water Damage: Magnesium and carbon fiber can handle a splash, but if water reaches the high-density BGAs (Ball Grid Arrays) on the Main PCB, it causes immediate short-circuiting and corrosion.


Key Features

  • Genuine OEM Component: Shipped with the factory-default firmware (which usually requires an immediate update to the latest version via the Blackmagic Camera Setup utility).

  • Precision Mounting: All mounting holes and thermal contact points are laser-aligned to ensure it fits perfectly within the internal magnesium sub-frame.

  • Integrated I/O: Most of the side connectors (except for those on auxiliary boards) are surface-mounted directly to this PCB for maximum signal integrity.


Technical Installation Note

Warning: This is a Level 4 (Expert) repair. It involves a total disassembly of the camera.

  1. Sensor Calibration: The Main PCB and the Sensor are a matched pair in terms of software. When you swap a Main PCB, you may need to perform a "Pixel Calibration" (found in the camera menu) to map out any dead pixels on your existing sensor.

  2. Thermal Compound: You must apply new high-grade thermal paste or replace the thermal pads on the primary processing chips. Without proper thermal coupling to the internal frame, the new PCB will overheat and shut down within minutes.

  3. Ribbon Cable Management: The 6K Pro is notoriously "busy" inside. There are numerous delicate ribbon cables (ZIF connectors) for the screen, the ND filters, the buttons, and the sensor. One small tear in these cables will render the new PCB useless.

  4. Static Discharge (ESD): You must work on a grounded anti-static mat. A single spark from your fingertip can destroy the sensitive gate logic on a new board before you even turn it on.

Expert Advice: If your camera is "dead," try a Force Recovery first. Hold the "Focus" button while powering on the camera via USB to see if the Blackmagic Camera Setup utility recognizes it in recovery mode. If it does, a firmware flash might save you from having to buy this expensive PCB!

Are you dealing with a camera that won't power on at all, or are you seeing specific "Processing Errors" on the screen?

Shipping Notes
  • Free Standard Shipping on $100+ Orders to the USA.
  • Except Preorder products are shipped in 48 hours.
  • Delivery to the USA:
  1. Standard Shipping : 3-10 business days
  • If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
  • We offer a 30-day return/exchange service after receiving.
  • Final sale items are not eligible for returns or exchanges.
  • To process your return/exchange, please contact us at [email protected]
  • Please click here for more details>>> Return & Exchange Policy
SKU: 5399944681

Discover Niche Categories That Outsell

Top-Converting Item to Boost Your Average Order

4.4 ★★★★★
Based on 5 reviews
Sort
Highest Rating
Newest First
Oldest First
Product Reviews
B
Verified Purchase
Benjamin Argabright
Bozeman, US
★★★★★ 5
My wife says its shiny and pretty!
Fits my 2005 Escape perfect. Works great!
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 12, 2026
T
Verified Purchase
Takota Lenfest
Battle Creek, US
★★★★★ 5
100%
This was definitely a great purchase! I put it in my moms truck and it works great no issues at all
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on November 26, 2025
A
Verified Purchase
Austin Birge
Port Orchard, US
★★★★★ 5
OE quality part!
Great product! A-Premium always comes in clutch with the affordable parts that are built well ! Fit perfectly on my 2011 Ford Escape 3.0. Only took me 20 minutes to install.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 13, 2026
W
Verified Purchase
wano81
Chelsea, US
★★★★★ 5
Quality part at a low price!
Low price for a quality part. Fit my 2006 Ford Escape perfectly and works great with no problems. Installed by a professional mechanic.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on October 11, 2025
I
Verified Purchase
Ignacio Cesar de los Reyes Pico
Boise, US
★★★★★ 5
Buenisimo
de manera confiable y enciende el vehículo sin problemas. Material resistente y duradero, fácil de instalar y compatible con el modelo del carro. Muy recomendable para mantener el vehículo en óptimas condiciones.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on October 2, 2025

recommand products