SKU: 76650310403

Cometic Mitsubishi Lancer EVO 4-9 85mm Bore .040 inch MLS Head Gasket 4G63 Motor 96-UP

$109.80 $122.00
Save 10%
No.2 Bestseller on nasasuma.com >

Pay in installments of $30.50 with ShopPay, AfterPay and Klarna

Shipping Estimate
USA
  • USA
  • CAN

Ships within 48 hours · Estimated delivery Aug 11 - Aug 16

Promo Codes Available:

For Your Every Summer RSVP, with Code: SUMMER15

Description

Cometic Mitsubishi Lancer EVO 4-9 85mm Bore .040 inch MLS Head Gasket 4G63 Motor 96-UPComprised of multiple embossed layers of stainless steel with the outer layers utilizing a Viton rubber coating. Compressed operating thickness is 0. 040". EVO 4 8. Cometic MLS (Multi Layer Steel) Head Gaskets provide maximum sealing performance for todays high output engines and require no sealants. MLS gaskets are ideal for both aluminum heads to aluminum blocks and aluminum heads to cast iron blocks. They can withstand the shearing force created by

Comprised of multiple embossed layers of stainless steel with the outer layers utilizing a Viton rubber coating. Compressed operating thickness is 0.040". EVO 4-8. Cometic MLS (Multi-Layer Steel) Head Gaskets provide maximum sealing performance for todays high output engines and require no sealants. MLS gaskets are ideal for both aluminum heads to aluminum blocks and aluminum heads to cast iron blocks. They can withstand the shearing force created by the two materials. MLS gaskets have increased strength because they are comprised of multiple layers of stainless steel; which also creates the ability to rebound and resist corrosion. The outer layers are embossed and coated on both sides with Viton (a flour elastomer rubber based material that is heat resistant to 250 C/ 482 F). Viton is designed to meet the demands of a variety of harsh sealing environments, load conditions, and surface finishes. The center or shim layer is uncoated stainless steel, which can be varied to accommodate multiple thickness requirements.

  • The embossed outer layers of the gaskets meet the demands of a variety of harsh sealing environments, load conditions, and surface finishes
  • The center or shim layer is an uncoated stainless steel layer which can be varied to accommodate multiple thickness requirements
  • Requires less clamp load creating less bore distortion
  • Conforms load distribution across the sealing area
  • Embossed Outer Layers Coated w/Viton

This Part Fits:

Year Make Model Submodel
2003-2005 Mitsubishi Lancer Evolution
2005 Mitsubishi Lancer Evolution MR
2005 Mitsubishi Lancer Evolution RS
Shipping Notes
  • Free Standard Shipping on $100+ Orders to the USA.
  • Except Preorder products are shipped in 48 hours.
  • Delivery to the USA:
  1. Standard Shipping : 3-10 business days
  • If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
  • We offer a 30-day return/exchange service after receiving.
  • Final sale items are not eligible for returns or exchanges.
  • To process your return/exchange, please contact us at [email protected]
  • Please click here for more details>>> Return & Exchange Policy
SKU: 76650310403

Discover Niche Categories That Outsell

Top-Converting Item to Boost Your Average Order

4.1 ★★★★★
Based on 12 reviews
Sort
Highest Rating
Newest First
Oldest First
Product Reviews
T
Verified Purchase
Tharin
Louisville, US
★★★★★ 5
BUY THIS ONE!
Model: NewSLS50_52
This is one of the good ones. There are other brands just as good, and manny brands are worse, but this handles well, rolls down easily, doesn't come off at all easily, and adapts to dips and curves like a champ. Appropriately heavy and dead, I'm happy with the way it smothers panel resonances and even at muffling direct sound, like a big hand over my Uncle Harry's eternally noisy mouth. You can rip the foil but you have to work hard at doing that. Remember to buy a brayer; you can roll overlaps nice and thin. Also remember to pre-wipe the sheet metal with a decent solvent like acetone or Stoddard/Varsol. It should last forever.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 26, 2025
H
Verified Purchase
Harvey
New York, US
★★★★★ 5
Good stuff, but watch the temp
Model: NewSLS50_52
I used this in my single cab pickup truck (89 ford.) It only took half the box (10 sheets or 25 square feet) to do the floors, but I bought the big box because I plan to do the doors, back wall, and maybe the roof as well. One thing I learned is that the temperature matters when you’re doing the installation. It was around 55F when I started in the evening, and when it dipped down into the 40s the sheets would not stick to the metal, and were hard to compress with the roller. That’s why I ended up only doing the floors and not any vertical surfaces; i will have to wait for a nice hot day. The other thing is that the foil layer on top is razor sharp at the edges, definitely wear gloves! I didn’t notice until after but I have little papercuts all over my fingers. Aside from those things, the install was easy and straightforward. The sheets cut easily with scissors, and any goo that ends up on your hands or scissors can be cleaned up with acetone (nail polish remover), or lacquer thinner. I would use this stuff again.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on November 16, 2023
L
Verified Purchase
Lyrah
Chelsea, US
★★★★★ 5
Very efficient!
Model: NewSLS50_52
Amazing the difference it makes on dumping the noise. Very easy to install. Pell and stick literally! Great!
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on November 23, 2025
J
Verified Purchase
Jak
Grantham, US
★★★★★ 5
Cost effective
Style: 8.7 sqft（8 pcs）, Material Type: Aluminum 197 mil
Nice, cost effective material. It stuck nicely to the door and was fairly easy to use. The grid marks on the back made it easy to cut. I would not rank it up with other materials in sound and heat isolation, but it did cut down the overall vibrations on the door panels and I did not feel heat immediately from the floor area as i did with bare metal. If you are working with a budget and want modest improvement, this material will work well over most stock materials.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on June 7, 2026
C
Verified Purchase
Carter Davis
Natrona Heights, US
★★★★★ 5
Good value and sticks well
Style: 8.7 sqft（8 pcs）, Material Type: Aluminum 197 mil, Style: 8.7 sqft（8 pcs）, Material Type: Aluminum 197 mil
For $14 for 8.7 square feet, this was more than enough to cover the important parts of the trunk of my 944. You DON'T need a roller to apply this, just strong hands and a well prepped surface. I vacuumed, lightly washed, then used 90% alcohol to clean the surface before applying. I could have used more and covered every inch, but there is diminishing returns in doing so (especially on a budget, or with a lower wattage sound system in my opinion). If this stuck as well as it did for me in a 45° garage, then it should stick just fine for you too. I will say, it is a little cheap feeling, but for the price I can't complain. There is an audible difference when knocking on the panels this material is applied to. I'm not a professional though, and if you're an audiophile, there are better options (but prepare to empty your wallet). Not sure I would do an entire vehicle with this material, but it is a great supplement.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on March 15, 2026

recommand products

Rick Owens Vintage Sneaker High SZ 45
300.00
Gold Tiny Eye
160.00
Stone Island Alligator Camo Cargo Shorts
188.95
Titanium Daith-Septum Clicker 21
35.00
Titanium Earring 170
40.00